Home page
Need help with your order?

Item Detail

IC7115GL
International Coatings 711 HP LB FF White Ink - 5 GL
Manufacturer Item:
Quantity Available: 10 5G
Sell Price: $380.00 5G
Next Quantity Break: 0
Next Quantity Break Discount: $0.00
Extended Price: $380.00
5G

 Extended Descriptions
 

APPLICATIONS

International Coatings 711 HP LB FF White Ink is a low fusing, fast flashing, high pigment white Non-Phthalate plastisol screen printing ink. With a very creamy viscosity, the ink is very easy to print. This results in a lot less pressure needed to print the ink through the screen. A truly white white, without any objectionable odor. The ink contains no bleaching agents and is superior in performance to other low bleed inks.



INSTRUCTIONS FOR HANDLING & USAGE:

International Coatings 711 HP LB FF White Ink is a low bleed, not a non-bleed ink. On some types of fabric, bleeding or dye migration may occur. Always test print the fabric to be printed before beginning production. It is best to do some long term testing on some fabrics to determine if they are going to bleed. Bleeding or dye migration may not occur right away. Excessive squeegee pressure will drive ink through fabric, making ink look less opaque. Adding too much reducer will also reduce opacity.


PHYSICAL PROPERTIES:

  • Low fusing, fast flashing, high pigment, white Non-Phalate (NP) plastisol screen printing ink.

  • A truly white white.

  • Exhibits excellent bleed resistance and stretch properties.

  • Creamy and easy to print through a variety of mesh counts with less pressure.

  • Contains no bleaching agents and has no odor.


Spot Flashing With International Coatings 711 HP LB FF White Ink:

711 Classic White will spot dry, with a very low after ash tack. Dwell time is dependent on the spot dryer used. In some cases, you may have to lower the heat of the spot cure unit because too much heat may actually make the ink tacky. When you spot dry, you are only partially fusing or gelling the surface of the ink. The ink should just ry to the touch, with no lift o, but not totally fused. Totally fusing the underprint white may cause inter-coat adhesion problems with the inks printed on top of the white ink. Final fusing or curing occur in the dryer.



Additional information For International Coatings 711 HP LB FF White Ink:

711 Classic White is a low bleed ink, not a non-bleed ink. On some types of fabric, bleeding or dye migration may occur. Always test print the fabric to be printed before beginning production. It is best to do some long term testing on fabrics to determine if they are going to bleed. Bleeding or dye migration may not occur right away. 711 Classic WhiteTM This technology helps make h , A Adding any reducers or additives can lower bleed resistance, opacity, or increase cure times of ink. the ink prior to printing on press and after addition of reducers or additives. Test dryer temperatures and wash test printed product before and during a production run.


Technical Specifications of International Coatings 711 HP LB FF White Ink:

Fabric Types: 100% Cotton/Polyester blends, and Polyester, Always test print fabric

for possible dye migration before beginning a production run.

Mesh: Count: 60 - 230 t/in (24 - 90 t/cm) Monofilament. Use 110-230 or 43-90 t/cm Monofilament Underbasing.

Squeegee: Durometer: 65-75, Sharp Edge 60-90-60 or 70-90-70 Triple Durometer Sharp Edge

Flash & Cure Temperatures: 275°F to 300°F (140°C to 149°C) entire ink film. Test dryer temperatures.

Storage: 65-90°F (18-32°C) Avoid direct sunlight. Keep container well sealed.

Clean Up: Any Eco Friendly plastisol screen wash.

 Warehouses
 
Warehouse Description Quantity Avail
10 Garston-East Hartford 4 5G
20 Garston-Haverhill 6 5G
30 Garston-Rochester 0 5G
#

Line Item Add

Item Number:
Quantity:
Unit of Measure: